NethServer Enterprise can act as firewall and gateway inside the network where it is installed. All traffic between computers on the local network and the Internet passes through the server that decides how to route packets and what rules to apply. Firewall mode is enabled only if the system has at least one network interface configured with red role.
The Firewall application can be installed from Software center and includes:
Multi WAN support up to 15 connections
Firewall rules management
Traffic shaping (QoS)
Routing rules to divert traffic on a specific WAN
Deep packet inspection (DPI)
Smart search to quickly find existing rules or objects
Real time charts
Real time charts display traffic and service statistics collected by Netdata. To avoid performance penalty on slow hardware, Netdata is not part of the firewall application and can be installed from Software center.
Apply and revert¶
Every time the firewall configuration has been changed, modifications are not applied immediately but saved in a temporary store. For the changes to take effect, click on the Apply button at the top right corner of the page.
As long as the new rules created have not been applied, you can revert all changes by clicking the Revert button at the top right corner of the page.
Each interface is identified with a color indicating its role within the system. See Network.
When a network packet passes through a firewall zone, the system evaluates a list of rules to decide whether traffic should be blocked or allowed. Policies are the default rules to be applied when the network traffic does not match any existing criteria.
Firewall policies allow inter-zone traffic accordingly to this schema:
GREEN -> BLUE -> ORANGE -> RED
Traffic is allowed from left to right, blocked from right to left.
To display the list of active policies click on the Policies button inside the Rules page.
Policies can be changed by creating specific rules between zones from the Rules page or by accessing the Traffic to Internet section inside the Settings page.
In this section you can change standard firewall behavior.
Traffic to Internet¶
The default firewall policy allows all traffic from green to red interfaces (Internet). To change the default policy for Internet access, enable or disable the Traffic to Internet (red interface) option. If disabled all traffic from green to red network is blocked. Specific traffic can be allowed creating rules from Rules page.
Traffic between VPNs¶
By default traffic between different VPN tunnels is not allowed, but sometimes you would need to allow it like when a OpenVPN roadwarrior client should reach a remote resource behind an IPsec tunnel. To permit traffic between VPNs, just enable the Traffic between OpenVPN roadwarrior, OpenVPN tunnels and IPSec tunnels option. Extra block rules can be created from Rules page to customize the network access between VPN zones.
Ping from Internet¶
Allows NethServer Enterprise to answer ICMP requests from red interfaces (Internet).
By default, all port forwards are available only for hosts inside the WAN. When Hairpin NAT is active, hosts on the local zones will be able to reach forwarded ports using both public and private firewall IP addresses.
Whenever possible it is recommended to avoid enabling this option and correctly configure split DNS to resolve service names inside the LAN.
If hair-pinning is still required, check the Enable hairpin NAT option.
This functionality requires NethServer Enterprise to have a public IP address on the red interface.
Application Layer Gateway (ALG)¶
Application layer gateways handle dynamic firewall rules for certain protocols. Many ALGs are enabled by default on NethServer Enterprise, to allow some protocols (such as FTP, SIP, etc) to operate through NAT. ALGs inspect and rewrite specific network packets and automatically open required ports.
Enable SIP-ALG and H.323-ALG
Some PBXs may not work properly with SIP-ALG and H.323-ALG. In case of audio and call problems with your PBX or your VoIP client try to disable them.
The firewall can use the list of DHCP reservations to strictly check all traffic generated from hosts inside local networks. DHCP server should could be disabled but the administrator must still create reservations to associate the IP with a MAC address. See DHCP and PXE server for more details.
When IP/MAC binding is enabled, the administrator will choose what policy will be applied to hosts without a DHCP reservation. The common use is to allow traffic only from known hosts and block all other traffic. In this case, hosts without a reservation will not be able to access the firewall nor the external network.
To enable traffic only from well-known hosts, follow these steps:
Create a DHCP reservation for a host
Go to Configure from the button menupage and select from
Select MAC validation (IP/MAC binding)
Choose Block traffic as the policy to apply to unregistered hosts
Remember to create at least one DHCP reservation before enabling the IP/MAC binding mode, otherwise, no hosts will be able to manage the server using the web interface or SSH.
Rules apply to all traffic passing through the firewall. When a network packet moves from one zone to another, the system looks among configured rules. If the packet matches a rule, the rule is applied.
Rule's order is very important. The system always applies the first rule that matches.
A rule consists of five main parts:
Time condition (optional)
Available actions are:
ACCEPT: accept the network traffic
REJECT: block the traffic and notify the sender host
DROP: block the traffic, packets are dropped and no notification is sent to the sender host
Source and destination fields accept built-in roles, Firewall objects and raw IPv4 addresses or CIDR. Such raw addresses can be later converted to firewall objects using the Create Host and Create CIDR subnet actions which will appear next to the address itself.
If VPN application is installed, there are also two extra zones available:
ivpn: all traffic from IPSec VPNs
ovpn: all traffic from OpenVPN VPNs
The configuration of firewall rules is split into two different pages:
Rules: manage rules applied only to the network traffic traversing the firewall.
Local rules: manage rules applied only to the network traffic generated from the firewall, or directed to the firewall itself.
When creating new rules, only the most common fields are shown. To show other less common parameters click the Advanced label.
If no red interface has been configured, the firewall will not generate rules for blue and orange zones.
REJECT vs DROP¶
As a general rule, you should use REJECT when you want to inform the source host that the port which it is trying to access is closed. Usually, the rules on the LAN side can use REJECT.
For connections from the Internet, it is recommended to use DROP, in order to minimize the information disclosed to any attacker.
When a rule matches the ongoing traffic, it's possible to register the event on a log file by checking the option from the web interface.
Firewall log is saved in
The log can be inspected from the command line or using the Logs page.
Deep Packet Inspection (DPI)¶
Deep Packet Inspection (DPI) is an advanced packet filtering technique.
When the DPI module is active, new items for the Service field are available in the Edit rule form. Those items are labeled DPI protocol, among the usual network service and service object items.
The DPI module uses the nDPI library which can identify around 250 types of network traffic split in network protocols (eg. OpenVPN, DNS) and web applications (eg. Netflix, Spotify).
Firewall rules using DPI services are generated inside the mangle table, for this reason such rules have some limitations:
reject action is not supported, use drop to block traffic
any and firewall can't be used as source or destination
route to provider X action is not supported: the identification of the protocol often begins after the connection has been already established, so the routing decision can't be changed
Even if DPI can identify traffic to/from specific web sites such as Facebook, it is better suited to block or shape protocols like VPN, FTP, etc. Web site access should be regulated using Web proxy.
Note that some DPI protocols (such as Amazon) can match large CDNs, so please do not block such protocols using DPI rules unless you want to prevent access to thousands of sites.
DPI markers are automatically applied also to the traffic which originates from the firewall itself, like HTTP traffic from the web proxy.
The complete list of DPI protocols, along with counters for matched traffic, is available inside the DPI page under the category on the left menu.
Rules on existing connections¶
When a new rule is created, as default, it is applied only to new connections. But in some scenarios, the administrator may need to apply the rule also on established connections.
If the option Apply to existing connections is enabled, the rule will be applied to all connections including already established ones.
Below there are some examples of rules.
Block all DNS traffic from the LAN to the Internet:
Service: DNS (UDP port 53)
Allow guest's network to access all the services listening on Server1:
The term WAN (Wide Area Network) refers to a public network outside the server, usually connected to the Internet. A provider is the company that actually manages the WAN link.
All WAN network interfaces are labeled with the red role and are listed on the top of the page, just below bandwidth usage charts. Rules can be created under the Rules section on the same page.
If the server has two or more configured red interfaces, it is required to correctly fill, Download bandwidth and Upload bandwidth fields from the Network page. Download and upload bandwidth can be automatically calculated using the Speedtest button.
Each provider represents a WAN connection and is associated with a network adapter. Each provider defines a weight: the higher the weight, the higher the priority of the network card associated with the provider.
The system can use WAN connections in two modes:
Balance: all providers are used simultaneously according to their weight
Active backup: providers are used one at a fly from the one with the highest weight. If the provider you are using loses its connection, all traffic will be diverted to the next provider.
To determine the status of a provider, the system sends an ICMP packet (ping) at regular intervals. If the number of dropped packets exceeds a certain threshold, the provider is disabled.
The administrator can configure the sensitivity of the monitoring through the following parameters:
Percentage of lost packets
Number of consecutive lost packets
Interval in seconds between sent packets
To change WAN mode and link monitoring options click on Configure button.
The network traffic can be routed to specific WANs by creating rules inside the Rules section on this page. After creating or editing rules, make sure to apply the changes. See Apply and revert for details.
Given two configured providers:
Provider1: network interface eth1, weight 100
Provider2: network interface eth0, weight 50
If balanced mode is selected, the server will route a double number of connections on Provider1 over Provider2.
If active backup mode is selected, the server will route all connections on Provider1; only if Provider1 becomes unavailable the connections will be redirected to Provider2.
The firewall blocks requests from public networks to private ones. For example, if a web server is running inside the LAN, only computers on the local network can access the service in the green zone. Any request made by a user outside the local network is blocked.
To allow any external user access to the web server you must create a port forward. A port forward is a rule that allows limited access to resources from outside of the LAN.
When you configure the server, you must choose the listening ports. The traffic from red interfaces will be redirected to selected ports. In the case of a web server, listening ports are usually port 80 (HTTP) and 443 (HTTPS).
When you create a port forward, you must specify at least the following parameters:
The source port
The destination port, which can be different from the origin port
The network protocol like TCP, UDP, TCP & UDP, AH, ESP or GRE
The address of the internal host to which the traffic should be redirected
It's possible to specify a port range using a colon as the separator in the source port field (eg: 1000:2000), in this case, the destination port field must be left empty
Port forwards are grouped by destination host and support raw IP addresses along with firewall objects.
By default, all port forwards are available only for hosts inside the WAN, see Hairpin NAT to change such behavior.
Given the following scenario:
Internal server with IP 192.168.1.10, named Server1
Web server listening on port 80 on Server1
SSH server listening on port 22 on Server1
Other services in the port range between 5000 and 6000 on Server1
If you want to make the web server available directly from public networks, you must create a rule like this:
origin port: 80
destination port: 80
host address: 192.168.1.10
All incoming traffic on the firewall's red interfaces on port 80, will be redirected to port 80 on Server1.
In case you want to make accessible from outside the SSH server on port 2222, you will have to create a port forward like this:
origin port: 2222
destination port: 22
host address: 192.168.1.10
All incoming traffic on the firewall's red interfaces on port 2222, will be redirected to port 22 on Server1.
In case you want to make accessible from outside the server on the whole port range between 5000 and 6000, you will have to create a port forward like this:
origin port: 5000:6000
host address: 192.168.1.10
All incoming traffic on the firewall's red interfaces on the port range between 5000 and 6000 will be redirected to the same ports on Server1.
By default, the field access to port forward is granted to anyone. You can restrict access to port forward only from some IP addresses or networks by adding entries to Restrict access to field. This configuration is useful when services should be available only from trusted IPs or networks.
Example of valid entries:
10.2.10.4: enable port forward for traffic coming from 10.2.10.4 IP
10.2.10.0/24: enable port forward only for traffic coming from 10.2.10.0/24 network
One-to-one source NAT (SNAT) is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses. If you have a bunch of public IP addresses and if you want to associate one of these to a specific network host, NAT 1:1 is the way. SNAT is available only if there is at least one IP alias configured on red network interfaces.
This feature only applies to network traffic from a host inside the local network to the public Internet. It does not affect in any way the traffic from the Internet toward the alias IP. If you need to route some specific traffic to the internal host use the port forward as usual.
If you need to route all traffic to the internal host (not recommended!) use a port forward with protocol TCP & UDP and source port 1:65535.
In our network we have a host called
example_host with IP
192.168.5.122. We have also associated a public IP address
18.104.22.168 as an alias of
eth0 interface (
We want to map our internal host (
192.168.5.122) with public IP
In the NAT 1:1 panel, we choose for the IP
22.214.171.124 (read-only field) the specific host (
example_host) from the combo-box. We have configured correctly the one-to-one NAT for our host.
Traffic shaping allows applying priority rules on network traffic through the firewall. In this way, it is possible to optimize the transmission, control the latency and tune the available bandwidth.
To enable traffic shaping it is necessary to know the exact amount of available download and upload bandwidth. Access the Network page and carefully set bandwidth values.
If download and upload bandwidth are not set for a red interface, traffic shaping rules will not be enabled for that interface.
Be sure to specify an accurate estimate of the bandwidth on network interfaces. To pick an appropriate setting, please do not trust the nominal value, but use the Speedtest button or online tools to test the real provider speed.
In case of congestion by the provider, there is nothing to do in order to improve performance.
Traffic shaping classes are used to commit bandwidth for specific network traffic. Configuration of traffic shaping is composed of 2 steps:
creation of traffic shaping classes
assignment of network traffic to a specific class
Traffic shaping is achieved by controlling how bandwidth is allocated to classes.
Each class can have a reserved rate. A reserved rate is the bandwidth a class will get only when it needs it. The spare bandwidth is the sum of not committed bandwidth, plus the committed bandwidth of a class but not currently used by the class itself.
Each class can have also a maximum rate. If set, the class can exceed its committed rate, up to the maximum rate. A class will exceed its committed rate only if there is spare bandwidth available.
Traffic shaping classes can be defined under Traffic shaping page. When creating a new class, fill the following fields.
Class name: a representative name
Description: optional description for the class
Limits under Download bandwidth limits section:
Min: minimum reserved download bandwidth, if empty no download reservation will be created
Max: maximum allowed download bandwidth, if empty no upper limit will be set
Limits under Upload bandwidth limits section:
Min: minimum reserved upload bandwidth, if empty no upload reservation will be created
Max: maximum allowed download bandwidth, if empty no upper limit will be created
For each class the bandwidth can be specified using the percentage of available network bandwidth or with absolutes values expressed in kbps. As default, a traffic shaping class is applied to all red network interfaces. Such behavior can be changed by selecting an existing red interfaces under the Bind to menu inside the Advanced section.
The system provides two pre-configured classes:
high: generic high priority traffic, can be assigned to something like SSH
low: low priority traffic, can be assigned to something like peer to peer file exchange
The system always tries to prevent traffic starvation under high network load.
Classes will get spare bandwidth proportionally to their committed rate. So if class A has 1Mbit committed rate and class B has 2Mbit committed rate, class B will get twice the spare bandwidth of class A. In all cases, all spare bandwidth will be given to them.
Network traffic can be shaped by creating rules under the Rules section in this page. After creating or editing rules, make sure to apply the changes.
For more info, see FireQOS tutorial.
Firewall objects are representations of network components and are useful to simplify the creation of rules.
There are 6 types of objects, 5 of them represent sources and destinations:
Host: representing local and remote computers. Example:
Groups of hosts: representing homogeneous groups of computers. Hosts in a host group should always be reachable using the same interface. Example:
IP ranges: a list of IP addresses expressed as a range. Example:
myrange, composed by IPs from
CIDR Networks: you can express a CIDR network in order to simplify firewall rules.
Example 1 : last 14 IP addresses of the network are assigned to servers (
192.168.0.240/28). Example 2 : you have multiple green interfaces but you want to create firewall rules only for one green (
Zone: representing networks of hosts, they must be expressed in CIDR notation. Their intended usage is for defining a part of a network with different firewall rules from those of the nominal interface. They are used for very specific needs.
By default, all hosts belonging to a zone are not allowed to do any type of traffic. It's necessary to create all the rules on the firewall in order to obtain the desired behavior.
Time conditions: can be associated to firewall rules to limit their effectiveness to a given period of time.
Rules which have time conditions are enforced only for new connections. Example: if you are blocking HTTP connections from 09:00 to 18:00, connections established before 09:00 will be allowed until closed. Any new connection after 09:00 will be dropped.
Services: a service listening on a host with at least one port and protocol. Example:
MAC addresses: a host identified by a MAC address. The MAC address must be bound to an existing zone.
When creating rules, you can use the records defined in DNS and DHCP and PXE server like host objects. In addition, each network interface with an associated role is automatically listed among the available zones.
This page keeps track of all active connections. Connections can be filter by Protocol and State. The list of connections is not refreshed in real time. To list new connections click the Refresh button.
The administrator can delete a single connection or flush the whole connection tracking table using Delete all connections button.